Table 10-2. Camera Link Connector Pin-out Signal Pin Signal Pin Signal Pin GND 1 CC2+ 10 X3+ 19 X0- 2 CC3- 11 SerTC- 20 X1- 3 CC4+ 12 SerTFG+ 21 X2- 4 GND 13 CC1+ 22 Xclk- 5 GND 14 CC2- 23 X3- 6 X0+ 15 CC3+ 24 SerTC+ 7 X1+ 16 CC4- 25 SerTFG- 8 X2+ 17 GND 26 CC1- 9 Xclk+ 18 Table 10-3. Bit Assignments when used in 12-bit data (S = 0) Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name ODD-00 Tx0 ODD-07 Tx5 EVEN-02 Tx19 EVEN-09 Tx14 ODD-01

         Tx1 ODD-08 Tx7 EVEN-03 Tx20 EVEN-10 Tx10 ODD-02 Tx2 ODD-09 Tx8 EVEN-04 Tx21 EVEN-11 Tx11 ODD-03 Tx3 ODD-10 Tx9 EVEN-05 Tx22 STROBE TxCLK ODD-04 Tx4 ODD-11 Tx12 EVEN-06 Tx16 LVAL Tx24 ODD-05 Tx6 EVEN-00 Tx15 EVEN-07 Tx17 ODD-06 Tx27 EVEN-01 Tx18 EVEN-08 Tx13 Table 10-4. Bit Assignments when used in 10-bit data (S = 1) Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name Bit DS90CR285 Pin Name ODD-00 Tx0 ODD-07 Tx5 EVEN-02 Tx19 EVEN-09 Tx14 ODD-01 Tx1 ODD-08 Tx7 EVEN-03 Tx20 NC Tx10 ODD-02 Tx2 ODD-09 Tx8 EVEN-04 Tx21 NC Tx11 ODD-03 Tx3 NC Tx9 EVEN-05 Tx22 STROBE TxCLK ODD-04 Tx4 NC Tx12 EVEN-06 Tx16 LVAL Tx24 ODD-05 Tx6 EVEN-00 Tx15 EVEN-07 Tx17 ODD-06 Tx27 EVEN-01 Tx18 EVEN-08 Tx13

        Mechanical Characteristics 11.1 Weight The camera typical weight (without lens nor lens adapter) is 220 g/7.7 ounces (typical). 11.2 Dimensions The camera dimensions (without lens) are W = 56 mm, H = 60 mm, L = 39.4 mm. Figure 11-1. Mechanical Box Drawing and Dimensions 15 15 6 39.4 12 4 x 2 holes M4 (on the 4 sides) 56 48 60 52 Sensor 1st pixel y = 30 ± 0.05 ∅ 42 H7 ∅ 46 z = 10.3 ± 0.03 Optical sensor plane to front face 1 3 x M2.5 at 120° x = refer to "Mechanical Mounting Reference" Reference mounting plane Reference mounting plane Reference mounting plane 

       Mechanical Mounting Reference The front panel mechanical part is designed to support the mounting of the camera. On this mechanical part, three surfaces are considered as mounting reference surface: i.e. the distance between these surfaces and the first active pixel are known very precisely (better than ±50 µm). 11.4 Sensor Alignment Figure 11-2. Sensor Alignment Diagram 11.5 Lens Mounting (Lens Not Supplied) The camera can be provided with three different lens adapter, corresponding to three different options. The user has to selected the correct adapter. The following table gives recommendations according to the sensor size. Table 11-1. Mechanical Mounting Reference Number of Pixels 512 1024 2048 4096 x with 14 µm sensor (nm) 24.416 20.832 13.664 – x with 10 µm sensor (nm) – 22.880 17.760 7.520 Y axis Z axis X axis X, Y plans x + ∆x y + ∆y z + ∆z ∆θx, y Mechanical reference point Mechanical reference point Active area Active area center First pixel center ∆tiltz